Before you buy a full-size ASIC, the most important question is not which model to choose. It is whether your electrical supply can run it safely, around the clock. A modern Bitcoin flagship draws roughly as much as a large electric heater, but it does so continuously, 24 hours a day. This guide covers the circuits, connectors, power distribution units (PDUs) and power supplies you need to plan for.
Safety first: this article is general information. Electrical codes differ by country, and high-power wiring should always be designed and installed by a qualified electrician.
How much power does an ASIC miner draw?
Typical published figures for current air-cooled machines:
- Antminer S21 XP: around 3,645 W
- Whatsminer M60S: around 3,441 W
- IceRiver KS7: around 3,500 W
- Hydro models: often 5,000 W or more
To turn watts into amps, divide by the voltage. An S21 XP at 3,645 W on a 240 V supply draws about 15.2 A. On 230 V it draws about 15.8 A.
Why 220–240 V matters
Full-size ASICs are designed for 220–240 V AC. Running on 110–120 V would double the current for the same power, which most miner power supplies do not support and most household circuits could not carry. In North America, that means a 240 V split-phase circuit, like those used for dryers and EV chargers. In most of Europe, Asia, Africa and the Middle East, standard mains is already 220–240 V, but you still need a circuit rated for the load.
The continuous-load rule
Miners run constantly, which electricians treat as a continuous load. Many codes, including the US National Electrical Code, limit continuous loads to 80% of the breaker rating. So:
- A 20 A, 240 V circuit supports about 16 A continuous, or roughly 3.8 kW: enough for one flagship miner.
- A 30 A, 240 V circuit supports about 24 A continuous, or roughly 5.7 kW.
Your local rules may differ. The point is to size circuits with headroom, never right at the limit.
Connectors and plug types
At the miner: C19 and C20
Most full-size miners use high-current IEC connectors. The miner or PSU has a C20 inlet, and the power cord ends in a C19 connector. These are rated for higher current than the C13 connectors used on PCs. Use a cord with conductors rated for the load; thin, generic cords can overheat.
At the wall: depends on your country
| Region | Common options | Notes |
|---|---|---|
| North America | NEMA 6-20, 6-30, L6-30 | 240 V receptacles; L6-30 is a locking type popular for miners |
| UK | IEC 60309 16 A or 32 A (commando) | A standard 13 A UK plug cannot safely carry a 3.6 kW miner continuously |
| Continental Europe | IEC 60309 16 A or 32 A; Schuko for lower loads | Schuko is rated 16 A; a dedicated industrial connector gives more headroom |
| Australia | 15 A or higher-rated outlets, IEC 60309 | Standard 10 A outlets are not suitable for flagship miners |
Check our parts and power category for C19 cords and adapters.
Power supplies (PSUs)
Most current flagship miners, including the S21 series and the Whatsminer M60 series, have integrated power supplies. Some older or specialist models use an external PSU, such as Bitmain’s APW units, which connects to the hashboards with dedicated cables.
If you need a replacement or external PSU:
- Match the output voltage and connector type to the miner.
- Choose a PSU rated comfortably above the miner’s draw.
- Confirm the input voltage range covers your supply.
- Use manufacturer-compatible units rather than unknown generic supplies.
PDUs: powering several miners
Once you run more than one or two machines, a power distribution unit keeps things safe and tidy. Mining PDUs typically take a single high-current or three-phase input and provide multiple C19 outlets, each with its own breaker.
What to look for in a PDU
- Input that matches your supply: single-phase or three-phase, at the right voltage
- Per-outlet or per-bank breakers
- Enough C19 outlets for your miners, with headroom
- Metering, if you want to track consumption per circuit
- Rack-mount or wall-mount format that fits your space
Three-phase PDUs are common at larger sites because they balance load across phases and deliver more power through one feed.
Common power mistakes
- Using extension cords or power strips. Household strips are not built for continuous 15 A loads and can overheat.
- Sharing a circuit with other appliances. A miner should have its own dedicated circuit.
- Running at the breaker limit. Leave headroom for continuous load.
- Ignoring voltage drop on long runs. Long cable runs need thicker conductors.
- Skipping the electrician. Insurance, safety and local rules all depend on proper installation.
Planning checklist
- List every miner and its published wattage.
- Convert to amps at your supply voltage.
- Size circuits with continuous-load headroom.
- Choose connectors and cords rated for the current.
- Add a PDU for multiple machines.
- Have a qualified electrician install and inspect everything.
Three-phase supplies
Larger sites often use three-phase power. Instead of one hot conductor, three are used, offset in timing, which delivers more power through one feed with smaller conductors. Miners are usually connected between phases or between a phase and neutral, depending on the supply and the PDU. Balancing the load across all three phases matters, so plan the layout with your electrician before connecting machines.
Get the right power gear
Browse PDUs, cords and PSUs in our parts and power range, then pick your miner from the shop. Need help choosing the right cord for your country? Contact us before you order.
Questions
Can I run an ASIC miner on 110 V?
Full-size ASICs are designed for 220u2013240 V. At 110u2013120 V the current would roughly double, which most miner power supplies and household circuits cannot handle.
What circuit size do I need for one Antminer S21 XP?
At around 3,645 W on 240 V it draws about 15.2 A. With an 80% continuous-load rule, a dedicated 20 A, 240 V circuit is a common starting point. Your electrician should confirm against local codes.
What plug does an ASIC miner use?
Most use a C20 inlet with a C19 power cord at the miner end. The wall end depends on your country, such as NEMA 6-20 or L6-30 in North America or IEC 60309 in the UK and Europe.
Do I need a PDU?
For one machine, a dedicated circuit and suitable outlet are enough. For several machines, a mining PDU with C19 outlets and per-outlet breakers is safer and easier to manage.



